AW: Greek characters in exported *.eps
- To: mathgroup at smc.vnet.net
- Subject: [mg27799] AW: [mg27739] Greek characters in exported *.eps
- From: Stefan.Schenderlein at ferring.de
- Date: Sat, 17 Mar 2001 05:41:24 -0500 (EST)
- Sender: owner-wri-mathgroup at wolfram.com
Paul J. Hinton mentioned the appropriate support page at Wolfram that
was
very helpful. GS has to be informed, where the Mathematica fonts are
stored
by adding a few lines in the fontmap file. Just a small addition. Under
Windows NT the GS 6.5 installation comes with a lot of fontmap.* files.
The
directory-entries for the fonts of Mathematica have to be made to
"fontmap.gs".
Thank you very much. Also thanks to Alois Steindl for the hints.
Stefan.Schenderlein at ferring.de
> Von: P.J. Hinton [SMTP:paulh at wolfram.com]
> An: Stefan.Schenderlein at ferring.de
> Betreff: Re: [mg27739] Greek characters in exported *.eps
>
> On Wed, 14 Mar 2001 Stefan.Schenderlein at ferring.de wrote:
>
> > A plot with a greek character \chi in the frame label was produced.
I
> > converted the textstyle because I do not like the courier numbers
on the
> > axis. Then the plot was exported as *.eps. The file was then
included
> into
> > a *.tex document. The dvi and ps output on Windows NT 4 using
miktex 2.0
> > showed the character properly. After transferring the *.eps to a
linux
> > environment (suse 7.0, tetex) the character is now shown as latin c
> instead
> > of \chi.
> >
> > Where is my mistake? Maybe due to the use of
> > TextStyle->{FontFamily->"Times"} Mathematica uses the installed
fonts
> that
> > are not available on the other computer. Can I install the fonts on
this
> > machine to get the proper output with latex?
> >
> > Thanks.
> > Stefan Schenderlein
> > stefan.schenderlein at ferring.de
> >
> >
> > Here is in detail what I tryed to do:
> >
> >
> > There is a function called chi (Flory-Huggins-Parameter of polymer
> solution
> > interaction) that is connected to a indirect measurable variable A2
> (second
> > virial coefficient) as following (rho - density, v molar volume):
> >
> > \!\(\[Chi][A2_] := \(-A2\)\ \(\[Rho]\_2\^2\) v\_1 + .5\)
> >
> > Some different rho and v are defined for some substances:
> >
> > \!\(\(THF = {\ v\_1 \[Rule] 81.11};\)\[IndentingNewLine]
> > \(DCM = {\ v\_1 \[Rule] 63.6};\)\[IndentingNewLine]
> > \(Toluol = {\ v\_1 \[Rule] 106.4};\)\[IndentingNewLine]
> > \(PLGA = {\[Rho]\_2 \[Rule] 1.35};\)\[IndentingNewLine]
> > \(PDMS = {\[Rho]\_2 \[Rule] 0.96};\)\)
> >
> > I plotted the function for different combinations of polymer /
solvent
> and
> > included a legend:
> >
> > <<Graphics`Legend`
> >
> > \!\(\(pic =
> > Plot[{\(\[Chi][A\_2] /. THF\) /. PLGA, \(\[Chi][A\_2] /.
DCM\) /.
> > PLGA, \(\[Chi][A\_2] /. DCM\) /.
> > PDMS, \(\[Chi][A\_2] /. Toluol\) /. PDMS}, {A\_2,
.000,
> .005},
> >
> > PlotStyle \[Rule] {Dashing[{ .08, .01}], Dashing[{ .04,
.01}],
> > Dashing[{ .06, .001, .02}], Dashing[{}]}, Frame
\[Rule]
> True,
> > Axes \[Rule] None,
> > TextStyle \[Rule] {FontFamily -> "\<Times\>",
> > FontSize \[Rule]
> > 8}, \[IndentingNewLine]FrameLabel \[Rule] \
> > {\*"\"\<\!\(A\_2\)\>\"", "\<\[Chi]\>"},
> > PlotLegend \[Rule] {"\<PLGA/THF\>", "\<PLGA/DCM\>",
> "\<PDMS/DCM\>",
> > "\
> > \<PDMS/Toluol\>"}, LegendShadow \[Rule] None,
> > LegendPosition \[Rule] {\(- .751\), \(- .52\)},
> > LegendTextSpace \[Rule] 2.5];\)\)
>
> You need to make sure that you PostScript interpretation device has
ready
> access to the Math fonts. This can be handled through either proper
> software configuration or through direct embedding. Both of these
topics
> are addressed in these FAQ pages.
>
> http://support.wolfram.com/Graphics/Formats/EPS/IncludeFonts.html
> http://support.wolfram.com/Graphics/Formats/EPS/Ghostscript.html
>
> --
> P.J. Hinton
> User Interface Programmer paulh at wolfram.com
> Wolfram Research, Inc.
>